Coltri MCH8 Breathing Air Quality: EN 12021, CGA Grade E and NFPA Testing Guide
Air quality is the reason a breathing-air compressor exists. This guide explains how to build a defensible testing programme around a Coltri MCH8: which standards apply, what each parameter's failure tells you about the machine, how often to sample, and how to document it.
1. Equipment overview
The Coltri MCH8 delivers roughly 130-140 L/min class at up to up to 330 bar, driven by single or three-phase electric motor, and is typically used for dive shops, fire stations, mobile refill vans. It is a mid-size portable unit with mixed short and long fills, which influences how often the filtration system needs attention.
| Parameter | Typical specification |
|---|---|
| Free air delivery | roughly 130-140 L/min class |
| Maximum working pressure | up to 330 bar |
| Drive | single or three-phase electric motor |
| Filtration | cartridge filtration system |
| Typical applications | dive shops, fire stations, mobile refill vans |
These values are typical market configurations. Confirm every value against the data plate and the manual of the individual unit before ordering parts or planning service.
2. The standards that matter
- EN 12021 - the European reference for breathing air, covering CO, CO2, oil, water and odour;
- CGA Grade E - the common North American specification for compressed air for breathing;
- NFPA 1989 - referenced by many fire-service programmes for breathing air quality and filling operations;
- Local occupational or diving authority requirements, which may be stricter than any of the above.
Always test against the edition and standard that applies at your site, and confirm the limits with your testing laboratory rather than with any secondary source.
3. Parameter limits and what a failure means
Breathing air is a life-safety product. In the EU the reference standard is EN 12021 (current edition), and in North America diving applications commonly reference CGA Grade E, while fire-service programmes often reference NFPA 1989 for breathing-air quality and filling operations. Limits differ between standards and editions, so always test against the edition in force at your site.
| Parameter | Indicative limit / requirement | What a failure usually points to |
|---|---|---|
| Carbon monoxide (CO) | Typical EN 12021 limit: max 5 ml/m3 (5 ppm) | Rising CO usually indicates intake contamination or overheated lubricant - check intake siting and stage temperatures |
| Carbon dioxide (CO2) | Typical EN 12021 limit: max 500 ml/m3 (500 ppm) | Elevated CO2 often traces to intake air drawn from a confined, occupied or engine-exhaust-affected area |
| Oil (lubricant mist) | Typical EN 12021 limit: max 0.5 mg/m3 | Oil carry-over points to separator, drain routine or a saturated cartridge |
| Water / humidity | Pressure dew point requirement to keep cylinders free of liquid water | Verify dryer performance, drain routine and cartridge condition |
| Odour and taste | No objectionable odour | Any detectable odour means stop using the gas and re-test before release |
A practical programme is: test every production batch or at the interval required by your authority, keep a written record of results, replace the filter cartridge by hours and by test result (whichever comes first), and re-test after any intervention on the filtration system. A Coltri MCH8 that passes its air test but shows a rising trend is telling you the cartridge or the intake environment needs attention before it fails a limit.
4. Faults that degrade air quality on this machine
| Symptom | Likely cause | How to confirm | Corrective action |
|---|---|---|---|
| Fill time extended versus commissioning | 1st-stage valve or intake filter restriction | Stage pressure comparison | Service valve, renew intake filter |
| Oil smell in delivered air | Separator drain blocked or saturated cartridge | Inspect drain and cartridge hours | Restore drain routine, replace cartridge |
| Thermal cut-out during back-to-back fills | Duty cycle exceeded or enclosure ventilation insufficient | Record run/rest ratio and cabinet temperature | Enforce duty cycle, improve ventilation |
| Belt squeal on start | Belt tension low or sheaves misaligned | Tension/alignment check | Tension or replace belt, align sheaves |
5. Sampling and documentation
- Sample at the point of use, not at the machine outlet only, and use a sampling method accepted by your laboratory.
- Set frequency by regulation, by throughput and by risk - batch testing is common for filling stations.
- Record result, date, operating hours since the last cartridge change, ambient conditions and the cartridge batch.
- Define an action level below the limit, so you investigate a rising trend before a result fails.
- Re-test after any filter, separator, valve or intake work, and after any overheating event.
6. Service scope
BAOSI / DEJUE (Shanghai) supplies high-pressure breathing-air compressors and also supports third-party service and consumables for mixed fleets. For the Coltri MCH8 and comparable units we can supply compatible filter cartridges, valve plate kits, belts, lubricants and seals, and provide troubleshooting support, overhaul guidance and annual maintenance planning. Where a brand-specific part number is required, we match it from your serial number and filter housing type.
Need parts or a second opinion on a fault? Send the model, serial number, operating hours and the recorded stage pressures or temperatures - our technical team will respond with a parts list and a diagnostic plan. Contact the BAOSI technical team.
Disclaimer: This article is provided for general reference only. Specifications vary by serial number, build year and market configuration - always verify against the original equipment manufacturer's manual and your unit's data plate before service. Work on high-pressure equipment should be performed by qualified, trained technicians, and any safety-critical repair should follow local regulations and the OEM procedure.